Standard is 100ft. and can be extended up to 400ft. for our PCP Pro model.

NO, hoses are reusable.

Yes, all material may be recycled back into storage containers after the job is completed. ♻️

The smallest is 2” however it does depend on the condition of the pipe (interior build-up, etc.) We do recommend brush coating for this size which can go down to 1.25”.

Also, spray head is 1.25” diameter and thus will make multiple coats a bit more challenging.

Raw material must be stored in a dry area and completely sealed.

PCP Micro can be managed with 1 technician, all other units should have 2 technicians at a minimum.

With tanks it’s approximately 160lbs.

Without tanks it’s approximately 120lbs.

Generally NO, as it is low viscosity, however in very low temps we do recommend heating first.

Cast iron, PVC, Metal, concrete, clay, terracotta, wood, steel.

Potable water pipes, yes, some our materials are NSF61 Chapter 5 approved. ✅

Yes, though there is a special procedure: cleaning, prepping, and priming, and coating.

Yes, we have specialized ULFM approved materials but it must be approved by local Fire Marshal first.

Yes, we’ve had several contractors who’s done so, especially under concrete slabs.

Yes, all pipes above 3” can be done with spray coating and anything under 3” must be brush coated.

NO, water must be removed.

You can use an industrial shop vac. and you can extend the vac. hose by using a pool hose. You can also wrap towels or sponges around pushrod camera and let the material soak up the water.

Pipe must be free of rust, debris, oil, and other contaminants.

Descaling and/or jetting machine, which are part of the package.

Pipe must be moisture-free.

Using air blower/dryer which is part of the package.

Most common issue is when the system is not cleaned properly causing the material to harden and or gum-up the in machine, requiring you to repair/replace certain parts.

None, machine is plug and play!

Most of our machines will work with 110V/15-20amps outlet but we recommend running the machines with a generator. Reason being, if there are too many sources utilizing the power source it may trigger the breaker.

Cannot fill holes with spray liner, however, you can remedy the problem by applying spot/point repair material first, which we do carry in stock and can provide for you.

We recommend to install CIPP liner or PipeSeal Pro sectional repair liner that we carry in stock and can provide for you.

Any existing opening, such as: clean-outs, roof vents, toilet flange.

Yes, with the PCP Pro or Pro MAX systems.

Yes

Yes, our PCP Pro & Pro Max come with multiple sized skids that give you the ability to go through transition pipes.

Yes, so long as the elbows are curved and not sharp angles.

Yes

Yes, with proper prep:

cleaning, priming, and coating

Yes, with proper preparation:

cleaning, priming, coating

Yes, however, it depends on pressure rating and condition of pipes.

Yes, so long as temp doesn’t exceed 230° F.

Up to 230° F, depending on material and usage (water vs. chem, etc.)

Yes, most of our products are chemical resistant depending on the type of chemicals (see chemical resistance test, we can provide a chemical resistance test for all materials we carry)

1 year Warranty.

All of our materials are “fast curing” with gel time between 5-30 seconds and re-coating may be done within a couple of minutes.

Depends on pipe size, i.e.: 4” diameter pipes, we recommend 3 coats which equals 120mils./3mm. (each coat is 40mils./1mm.) wall thickness.

Each coat takes approximately 10-15 minutes.

Yes, utilizing our specialized check-valves that open with a specific amount of pressure that keeps the material from running into the spray head.

You can, however, the system does come with an automated pulling device.

Generally, 30mins each.

System = 2 years

Material = 1 year

Depends on the installer, which in some cases can be up to 50 years.

We provide 24/7 support for both.

All materials and parts are supplied by us or an authorized distributor.

Up to 10 days for PCP Pro & Pro Max.

Machine and materials are MADE IN THE U.S.A.🇺🇲